Conducted Immunity

4 kHz–1 GHz, 110W

Manufactured exactly in accordance with the drawings and specifications of ISO 7637-3 for capacitively coupling the transients onto cables and wiring harnesses. With its characteristic impedance of 50 Ω , connected to the generator via a coaxial cable and terminated on the far side with a 50 Ω load resistor.

The VDS 200Q series is used to simulate the various battery supply waveforms recommended by international standards and by car manufacturer requirements. Available to rent!

The three-phase coupling/decoupling networks of the coupling NX series are used to couple EFT/Burst-, Surge- and Ring wave pulses on DC-lines or to three-phase (4-wire or 5-wire) mains supply systems for voltages up to 1,000 VDC / 3 x 690 VAC.

Haefely AXOS5 Compact Immunity Tester combines 5kV Burst/EFT, Surge combination wave, AC/DC Dips & Interrupts, along with an integrated single-phase coupling/decoupling network (CDN) into one compact system.

Turn Key Automotive System

With integrated power amplifier 80 W module 150 kHz–230 MHz

The EM Test ESD NX30 is an ESD tester to simulate ESD pulses at higher voltages up to 30 kV in both air and contact discharge mode. It satisfies requirements exceeding the EN/IEC 61000-4-2 test levels and complies with automotive test applications.

The Teseq NSG 4060 is an EMC immunity test system for the frequency range of 15 Hz - 150 kHz

Compact immunity test system NSG 4070C, 4 kHz–1 GHz RF generator and power meter (with integrated power amplifier 45 W module 9 kHz–1 GHz)

EM Test CWS 500N4Simulator for conducted, common-mode disturbances, as per IEC 61000-4-16, IEC 61000-4-19 Annex C, 0Hz (DC) to 165kHz

EM Test CWS 500N1 Continuous Wave Simulator for IEC 61000-4-6

Key applications of the CWS 500N3 are in the automotive and aerospace area. Various international standards and MIL requirements call for magnetic field tests in the low frequency range. Apart from this the automotive industry requires conducted immunity tests with superposed sinusoidal signals on the DC supply voltage (ripple noise). For both applications the CWS 500N3 is the perfect equipment including everything in a single box, necessary for these tests. The CWS 500N3 meets requirements of SAE J1113-2, ISO 11452-8, DO 160D/E Section 18 and MIL-STD-461 D/E/F/G CS101, CS109 and RS101.

The Haefely ONYX 30 ESD Simulator/Gun, 30kV has been specially designed to meet all latest international standards, including IEC61000-4-2 edition 2, and are the most ergonomic battery and AC power operated 30kV guns on the market. Test with confidence®.

Haefely ONYX 16 ESD Simulator/Gun, 16kV has been specially designed to meet all latest international standards, including IEC61000-4-2 edition 2, and are the most ergonomic battery and AC power operated 16kV guns on the market.

Teseq NSG 437-AUTOMOTIVE ESD Simulator/Gun, 30kV includes: Discharge Pistol, IEC 61000-4-2 330 Ohm/150pF High Voltage Network, Mains adapter / charging unit 80 – 240VAC, Ground cable, User manual

16.5kV Air, 9kV Contact

30kV ESD Simulator/Gun with built in charge remover

EMC Partner ESD3000 handheld ESD generator/tester with modular discharge circuits up to 30KV.

Automatic Power Line Frequency Magnetic Field

Designed for Teseq NSG 437 and 3438

Designed for Teseq NSG 438A Automotive

Teseq NSG 437 ESD Simulator/Gun, 30kV Includes: Discharge Pistol, IEC 61000-4-2 330 Ohm/150pF High Voltage Network, Mains adapter / charging unit 80 – 240VAC, Ground cable, User manual

The MPL MZ15 ESD Simulator Gun for IEC 1000-4-2 compliance testing. Includes 150pF/330 ohm discharge network, TPA-1, TPA-2, TPC-2A discharge tips, battery charger, carrying case.

ESD Charge Remover

The Teseq INA 417B Opto-link to a PC product is compatible of Teseq NSG 438A

ESD measurement target conforming to IEC/EN 61000-4-2

Target for precise ESD pulse measurements, very small insertion loss variation, precise gold plated construction

500pF/5000Ohm

330pF/330Ohm

ISO 10605 150pF/2kOhm