Close
You have no items in your shopping cart.
Search

CE Marking

CE marking is used to indicate that a product meets the European Union's (EU) standards for health, safety, and environmental protection. The CE mark is a requirement for the distribution of a variety of products in the EU. Meeting the safety requirements to receive CE marking is not a standard, but rather a legal requirement of the EU. When a manufacturer marks a product with the CE mark, they are declaring that it meets all of the legal requirements associated with CE marking. The CE mark allows products to be sold within the European Economic Area (EEA) without restrictions.

Rent or purchase equipment to certify your electrical product with the CE Mark from Avalon Test Equipment and Test With Confidence®.

3 Items in Grid 4 Items in Grid List

3ctest EDS 16H Electrostatic Discharge Simulator

Up to 16 kV, IEC/EN 61000-4-2 Compliance

A.H. Systems AEH-511 Azimuth & Elevation Head

Used to assist the test engineer in pointing the mounted test antenna towards the device under test.

A.H. Systems CPF-531 Calibration Fixture for RF Current Probes

The AH Systems CPF-531 Current Monitoring Probe Calibration Fixture is a great way to keep your broadband Current Probes, and Injection Current Probes calibrated and up to date.

A.H. Systems CPF-532 Calibration Fixture

offers a frequency range of 10 kHz–400 MHz

A.H. Systems CPF-631 Current Probe Calibration Fixture

Great way to keep your broadband Current Probes, and Injection Current Probes calibrated and up to date. Their rugged design ensures long life, and faultless operation over the wide calibration frequency range of 400 MHz- 1.5 GHz.

CNI 503 3-Phase Coupling Decoupling Network

The three-phase coupling/decoupling networks of the CNI 503x series are used to couple EFT/Burst pulses and Surge pulses on DC-lines or to three-phase (4-wire or 5-wire supply lines) mains supply systems for voltages up to 1,000VDC / 3x690VAC.

Com-Power ISN Calibration Kit for ISN and LCL Adapters

Measurements for common mode impedance, phase angle, voltage division factor, decoupling attenuation (isolation) and longitudinal conversion loss (LCL)

EM Test DPA 503N 3-Phase Power Analyzer With Harmonics & Flicker

The DPA 503N is used for 3-phase applications but also supports single phase applications.

EM Test ACS 503N30 AC Voltage Source

The EM Test ACS 503N30 is a three-phase AC sources, specifically designed for harmonics and flicker testing.

EM Test CA EFT Kit Load Resistors for EFT/Burst Verification

Includes the load resistors and a set of adapter to connect the coaxial matching resistors appropriately to the DUT output port; 50 ohm

EM Test CCI Capacitive EFT Coupling Clamp

The CCI is used to couple EFT/burst pulses to I/O lines as required in different European and international standards for immunity testing.

EM Test Compact NX7 Multifunctional Test Generator

The three-phase coupling/decoupling networks of the coupling NX series are used to couple EFT/Burst-, Surge- and Ring wave pulses on DC-lines or to three-phase (4-wire or 5-wire) mains supply systems for voltages up to 1,000 VDC / 3 x 690 VAC.

EM Test CWS 500N1 Continuous Wave Simulator

EM Test CWS 500N1 Continuous Wave Simulator for IEC 61000-4-6

EM Test CWS 500N1.4 Test Generator

RF Conducted Immunity Test System

EM Test CWS 500N3 Test Generator

Key applications of the CWS 500N3 are in the automotive and aerospace area. Various international standards and MIL requirements call for magnetic field tests in the low frequency range. Apart from this the automotive industry requires conducted immunity tests with superposed sinusoidal signals on the DC supply voltage (ripple noise). For both applications the CWS 500N3 is the perfect equipment including everything in a single box, necessary for these tests. The CWS 500N3 meets requirements of SAE J1113-2, ISO 11452-8, DO 160D/E Section 18 and MIL-STD-461 D/E/F/G CS101, CS109 and RS101.

EM Test CWS 500N4 Simulator for Conducted, Common-Mode Disturbances

EM Test CWS 500N4Simulator for conducted, common-mode disturbances, as per IEC 61000-4-16, IEC 61000-4-19 Annex C, 0Hz (DC) to 165kHz

EM Test EFT 500N5 Electrical Fast Transient/EFTBurst Simulator

The EFT 500N5 series are the state-of-the-art EFT/Burst testers with a built-in coupling/decoupling network for single phase or three-phase mains supply lines and a HV terminal to connect a capacitive coupling clamp.

EM Test EFT 500N8.1 Burst Generator

EFT 500Nx series – an EFT/Burst generator – is an intelligent solution offering exactly what you need for full-compliance immunity tests against Electrical/Fast transients phenomena. The distinct operation features, convenient EUT connection facilities, a clearly arranged menu structure and display philosophy as well as the pre-programmed standard test routines make testing easy, reliable and safe.

EM Test ESD NX30 ESD Simulator/Gun

The EM Test ESD NX30 is an ESD tester to simulate ESD pulses at higher voltages up to 30 kV in both air and contact discharge mode. It satisfies requirements exceeding the EN/IEC 61000-4-2 test levels and complies with automotive test applications.

EM Test OCS 500N6 Series Oscillatory Wave Simulator

EM Test OCS 500N6 Compact Tester for Ringwave and Damped Oscillatory Waves

EM Test OCS 500N6F Fast Damped Oscillatory Wave Generator

The OCS 500N6F series includes the test capabilities for fast damped oscillatory waves at 3 MHz, 10 MHz and 30 MHz up to 4.4kV and is extendable for slow damped oscillatory waves at 100 kHz / 1 MHz up to 3.0 kV (as per EN/IEC 61000-4-18) and for ringwave up to 6 kV as per EN/IEC 61000-4-12.

EM Test PFM 200N100.1 Automotive Power Fail Simulator

The EM Test PFM 200N100.1 has been designed to fully meet the requirements for E10, E13 and E14 of the LV 124 and the E48-09 of the LV 148. It also allows to perform microinterruptions with fast rise/fall time of as low as 200ns as required by GMW 3172, sec. 9.2.18

EM Test PFS 503N32 Power Fail Simulator

Electronic and electrical equipment may be affected by voltage dips, short interruptions and voltage variations of the power supply. Dips and interruptions are caused by faults in the public supply network, in installations or by sudden large change of load. Testing to such phenomena is required to proof that electronic and electrical equipment do not fall into unsafe operation conditions. EM TEST offers a full range of simulators up to 3x690VAC, 100A and DC voltage capability of up to 600V.

EM Test UCS 500N5 Multifunctional Test Generator

For Transients (EFT/Burst, Surge, and Power Fail) Up to 5.5KV

EM Test UCS500N7 Multifunctional Transient Immunity Simulator

The EM Test UCS500N7 Multifunctional Transient Immunity Simulator includes everything necessary to conduct fully compliant tests at levels that go far beyond common test requirements. Surge can be tested up to 7.0kV either according to IEC/EN 61000-4-5 or ANSI/IEEE C62.41. The UCS 500N7 offers an integrated Ringwave module (optional) as per ANSI/IEEE C62.41 and IEC/EN 61000-4-12 for ringwave tests on mains supply lines.

EM Test VSS 500N10

High Voltage Transient Surge Simulator

EMC Partner ESD3000 Handheld ESD Generator; up to 30KV

EMC Partner ESD3000 handheld ESD generator/tester with modular discharge circuits up to 30KV.

Haefely AXOS5 Compact Immunity Test System

Haefely AXOS5 Compact Immunity Tester combines 5kV Burst/EFT, Surge combination wave, AC/DC Dips & Interrupts, along with an integrated single-phase coupling/decoupling network (CDN) into one compact system.

Haefely AXOS8 Compact Immunity Test System

Haefely AXOS8 Compact Immunity Test System, 7 kV integrates all of the best features of several stand-alone test systems into one single economic solution. Standards: IEC/EN 61000-4-4, -4-5, -4-9, -4-11, -4-12